# BME 680 not detected on raspberry Pi 3B+

**URL:** <https://forum.core-electronics.com.au/t/bme-680-not-detected-on-raspberry-pi-3b/15375>\
**Category:** Support\
**Created:** [16 October 2022 03:59 UTC](https://forum.core-electronics.com.au/t/bme-680-not-detected-on-raspberry-pi-3b/15375 "2022-10-16T03:59:42Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![David148064](https://avatars.discourse-cdn.com/v4/letter/d/45deac/32.png) [@David148064](https://forum.core-electronics.com.au/u/David148064)\
**Post date:** [16 October 2022 03:59 UTC](https://forum.core-electronics.com.au/t/bme-680-not-detected-on-raspberry-pi-3b/15375/1 "2022-10-16T03:59:42Z")

</div>

Hello

I purchased the Pimoroni PIM375 BME680 fom Core Electronics. I soldered on the female dupont connector, and have used dupont leads to connect it to the raspberry pi. I used pins:

pin 17 3.3v  
pin 3 GPIO 8  
pin 5 GPIO 9  
NO wire  
pin 25 ground

I am using pin 1, 7, 9 for other sensors.

I installed the support modules as per the curl command on here:

> **[GitHub - pimoroni/bme680-python: Python library for the BME680 gas,...](https://github.com/pimoroni/bme680-python)**
>
> Python library for the BME680 gas, temperature, humidity and pressure sensor. - GitHub - pimoroni/bme680-python: Python library for the BME680 gas, temperature, humidity and pressure sensor.

And I tried to run python read-all.py from here:

> **[Getting Started with BME680 Breakout](https://learn.pimoroni.com/article/getting-started-with-bme680-breakout)**
>
> Learn how to solder and use your BME680 breakout – Pimoroni Learning Portal

This script does not see the BME680 on any of the two addresses.

I have checked the wiring many times. I checked the solder and it is good. I rebooted the Pi3B+. I performed the manual, install steps in the link below.

> **[Getting Started with BME680 Breakout](https://learn.pimoroni.com/article/getting-started-with-bme680-breakout)**
>
> Learn how to solder and use your BME680 breakout – Pimoroni Learning Portal

The pi is running the latest Bullsey raspbian, from an SSD plugged into the USB port.

Is there anything I should start with to determine why the BME680 is not being recognised?

Thanks

---

<div class="post-metadata">

**Author:** ![Rooppoor212784](https://avatars.discourse-cdn.com/v4/letter/r/278dde/32.png) [@Rooppoor212784](https://forum.core-electronics.com.au/u/Rooppoor212784)\
**Post date:** [16 October 2022 10:02 UTC](https://forum.core-electronics.com.au/t/bme-680-not-detected-on-raspberry-pi-3b/15375/2 "2022-10-16T10:02:34Z")

</div>

You can test the BME680 separately. With an Arduino UNO.

---

<div class="post-metadata">

**Author:** ![David148064](https://avatars.discourse-cdn.com/v4/letter/d/45deac/32.png) [@David148064](https://forum.core-electronics.com.au/u/David148064)\
**Post date:** [16 October 2022 22:12 UTC](https://forum.core-electronics.com.au/t/bme-680-not-detected-on-raspberry-pi-3b/15375/3 "2022-10-16T22:12:03Z")

</div>

> [@Rooppoor212784](#):
>
> With an Arduino UNO.

Unfortunately, I do not have an Arduino.

---

<div class="post-metadata">

**Author:** ![Rooppoor212784](https://avatars.discourse-cdn.com/v4/letter/r/278dde/32.png) [@Rooppoor212784](https://forum.core-electronics.com.au/u/Rooppoor212784)\
**Post date:** [25 October 2022 10:53 UTC](https://forum.core-electronics.com.au/t/bme-680-not-detected-on-raspberry-pi-3b/15375/4 "2022-10-25T10:53:10Z")

</div>

Oh! At least that way you could verify if the BME680 is really working or faulty. If you still have any warranty valid, you can send your sensor to the supplier.

---

<div class="post-metadata">

**Author:** ![Trent5487676](https://yyz2.discourse-cdn.com/flex028/user_avatar/forum.core-electronics.com.au/trent5487676/32/4583_2.png) [@Trent5487676](https://forum.core-electronics.com.au/u/Trent5487676)\
**Post date:** [4 November 2022 01:29 UTC](https://forum.core-electronics.com.au/t/bme-680-not-detected-on-raspberry-pi-3b/15375/5 "2022-11-04T01:29:52Z")

</div>

Hi David,

Sorry we missed your post earlier.

> [@David148064](#):
>
> pin 17 3.3v  
> pin 3 GPIO 8  
> pin 5 GPIO 9  
> NO wire  
> pin 25 ground
> 
> I am using pin 1, 7, 9 for other sensors.

GPIO 8 and 9 are not pin 3 and 5 on your Raspberry Pi alse GPIO 8 and 9 are not connected to the I2C bus.  
Physical pin 3 is GPIO 2 and Pin 5 is GPIO 3 on the Raspberry Pi. You can check which pins have I2C bus access using the link below.

> **[I2C at Raspberry Pi GPIO Pinout](https://pinout.xyz/pinout/i2c)**
>
> Raspberry Pi I2C pins

Can you please send us a photo of how you’ve got your sensor wired to the Raspberry Pi?

Once we know the pin numbers are right you can ask the Pi to scan for the sensor using the command `i2cdetect` there is a guide covering that I’ll link below.

> **[How to Scan and Detect I2C Addresses](https://learn.adafruit.com/scanning-i2c-addresses/raspberry-pi)**
>
> I2C is a common circuit interconnection format. This guide assists in helping a microcontroller/Raspberry Pi to find a connected I2C device.
