# Hakko T18 series tips

**URL:** <https://forum.core-electronics.com.au/t/hakko-t18-series-tips/11565>\
**Category:** Tools\
**Created:** [28 September 2021 04:10 UTC](https://forum.core-electronics.com.au/t/hakko-t18-series-tips/11565 "2021-09-28T04:10:51Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![Robert93820](https://avatars.discourse-cdn.com/v4/letter/r/ac91a4/32.png) [@Robert93820](https://forum.core-electronics.com.au/u/Robert93820)\
**Post date:** [28 September 2021 04:10 UTC](https://forum.core-electronics.com.au/t/hakko-t18-series-tips/11565/1 "2021-09-28T04:10:51Z")

</div>

One for the Core support guys  
Could you please provide some dimensions for the Hakko T18 series iron tips.  
The “business end” dimensions are there but the ones I am interested in are:  
The main barrel outside diameter and length.  
The hole (where the element fits) diameter and depth.

The reason for my request is I have a perfectly good controlled temp solder station but the available range of tips is not great and seems to be a bit scarce and these look as if they have a chance of fitting OK.

These dimensions do not seem to be published anywhere so will probably require measuring.  
Thanks in anticipation  
Cheers Bob

---

<div class="post-metadata">

**Author:** ![James](https://yyz2.discourse-cdn.com/flex028/user_avatar/forum.core-electronics.com.au/james/32/4400_2.png) [@James](https://forum.core-electronics.com.au/u/James)\
**Post date:** [28 September 2021 05:48 UTC](https://forum.core-electronics.com.au/t/hakko-t18-series-tips/11565/2 "2021-09-28T05:48:39Z")

</div>

Hi Bob,

Dimensions are as follows:  
Barrel OD: 6.8mm  
Barrel ID: 4mm  
Barrel Depth: 23.5mm

Hope this clears things up!  
-James

---

<div class="post-metadata">

**Author:** ![Robert93820](https://avatars.discourse-cdn.com/v4/letter/r/ac91a4/32.png) [@Robert93820](https://forum.core-electronics.com.au/u/Robert93820)\
**Post date:** [28 September 2021 05:53 UTC](https://forum.core-electronics.com.au/t/hakko-t18-series-tips/11565/3 "2021-09-28T05:53:07Z")

</div>

Hi James  
Thanks for that. Will investigate further  
Cheers Bob  
Edit:  
Looks they might do the job. Thanks

---

<div class="post-metadata">

**Author:** ![Robert93820](https://avatars.discourse-cdn.com/v4/letter/r/ac91a4/32.png) [@Robert93820](https://forum.core-electronics.com.au/u/Robert93820)\
**Post date:** [5 October 2021 09:06 UTC](https://forum.core-electronics.com.au/t/hakko-t18-series-tips/11565/4 "2021-10-05T09:06:39Z")

</div>

Hi All interested parties  
Follow up to my original post requesting dimensions.  
James very kindly measured the Hakko T18 series tips for me, thank you.

My soldering station is a Goot RX-711AS 65W power and control unit with a RX-70G 60W hand piece.Claimed ESD safe. This has been a good unit and is still working well but the tips are hard to find and a limited range (2). I had previously found a 3rd type for a 240V iron but had to have it cut down to fit my unit. This worked OK but recently I had occasion to investigate further

I was looking at Hakko but it seemed a waste to discard a perfectly good unit just for the want of an assortment of tips. I purchased 3 tips to try (from Core) and found the only real difference to be the body length, 1mm shorter than Goot tips. The tip retaining collar handled this difference OK so I now have a Goot iron fitted with Hakko tips seemingly working well. If this had not worked I would have had to invest a couple of hundred dollars in a Hakko anyway so the tips would have been used whatever the outcome.

A simple success story (for a change)  
Cheers Bob
