# Pico Dev and Stemma QT

**URL:** <https://forum.core-electronics.com.au/t/pico-dev-and-stemma-qt/16267>\
**Category:** Uncategorized\
**Created:** [1 February 2023 09:14 UTC](https://forum.core-electronics.com.au/t/pico-dev-and-stemma-qt/16267 "2023-02-01T09:14:04Z")\
**Posts on this page:** 7\
**Page:** 1

<div class="post-metadata">

**Author:** ![John136772](https://yyz2.discourse-cdn.com/flex028/user_avatar/forum.core-electronics.com.au/john136772/32/5416_2.png) [@John136772](https://forum.core-electronics.com.au/u/John136772)\
**Post date:** [1 February 2023 09:14 UTC](https://forum.core-electronics.com.au/t/pico-dev-and-stemma-qt/16267/1 "2023-02-01T09:14:04Z")

</div>

Can someone confirm that the I2C connections for these are compatible. I am assuming they are since I bought a Feather from Core which uses Stemma QT and a OLED that uses Pico Dev.

---

<div class="post-metadata">

**Author:** ![Michael](https://yyz2.discourse-cdn.com/flex028/user_avatar/forum.core-electronics.com.au/michael/32/3545_2.png) [@Michael](https://forum.core-electronics.com.au/u/Michael)\
**Post date:** [1 February 2023 22:24 UTC](https://forum.core-electronics.com.au/t/pico-dev-and-stemma-qt/16267/2 "2023-02-01T22:24:16Z")

</div>

Hey @John136772 They are absolutely pin compatible. 😃

There are some differences between the systems: Stemma can work at 5V and PiicoDev is strictly 3.3V. No problem if you’re sticking to a 3.3V system.  
Where the same device is used in both families there might be subtle differences eg. a PiicoDev and Stemma device may not share the same default address.

Recently I’ve been mucking around with a Stemma IR Camera connected to a Pico using the PiicoDev Expansion Board - no worries!

 ![2023-02-02_09-22-17_IMG_3179](https://canada1.discourse-cdn.com/flex028/uploads/core_electronics/original/2X/5/5f75561a22d20e9f28363c27cc62a001f277faff.jpeg)

---

<div class="post-metadata">

**Author:** ![John136772](https://yyz2.discourse-cdn.com/flex028/user_avatar/forum.core-electronics.com.au/john136772/32/5416_2.png) [@John136772](https://forum.core-electronics.com.au/u/John136772)\
**Post date:** [1 February 2023 22:42 UTC](https://forum.core-electronics.com.au/t/pico-dev-and-stemma-qt/16267/3 "2023-02-01T22:42:36Z")

</div>

Great! Thanks, I don’t use 5V much, I prefer the microcontrollers on 3.3V since they tend to be more capable. The addresses aren’t a problem I, usually use a scanning program to find them if the default doesn’t work. I will be plugging a Pico Dev Oled into a feather should be fine then.

---

<div class="post-metadata">

**Author:** ![John136772](https://yyz2.discourse-cdn.com/flex028/user_avatar/forum.core-electronics.com.au/john136772/32/5416_2.png) [@John136772](https://forum.core-electronics.com.au/u/John136772)\
**Post date:** [12 February 2023 10:21 UTC](https://forum.core-electronics.com.au/t/pico-dev-and-stemma-qt/16267/4 "2023-02-12T10:21:30Z")

</div>

Can I assume that Grove connectors are compatible with PiicoDev for I2C as well, (with the same 3.3V proviso)?  
I understand Grove aims to be a superset of connectors with Uart, analogue etc, but I am not interested in these.  
I found an article on TomsHardware that said Grove and Stemma were compatible.

> **[Stemma, Qwiic and Grove Connectors: Which is Right for You?](https://www.tomshardware.com/features/stemma-vs-qwiic-vs-grove-connectors)**
>
> Identify the right connector for your electronics projects

---

<div class="post-metadata">

**Author:** ![Liam120347](https://yyz2.discourse-cdn.com/flex028/user_avatar/forum.core-electronics.com.au/liam120347/32/5003_2.png) [@Liam120347](https://forum.core-electronics.com.au/u/Liam120347)\
**Post date:** [12 February 2023 10:42 UTC](https://forum.core-electronics.com.au/t/pico-dev-and-stemma-qt/16267/5 "2023-02-12T10:42:45Z")

</div>

Hi John,

Stemma+Grove and Stemma QT+PiicoDev use a different connector so an adapter cable would be required: [Grove to STEMMA QT / Qwiic / JST SH Cable - 100mm long | Adafruit ADA4528 | Core Electronics Australia](https://core-electronics.com.au/grove-to-stemma-qt-qwiic-jst-sh-cable-100mm-long.html)

If you have some PiicoDev prototyping cables you might be able to whittle down one side to get them to fit if you need to use em quickly!

---

<div class="post-metadata">

**Author:** ![John136772](https://yyz2.discourse-cdn.com/flex028/user_avatar/forum.core-electronics.com.au/john136772/32/5416_2.png) [@John136772](https://forum.core-electronics.com.au/u/John136772)\
**Post date:** [12 February 2023 10:49 UTC](https://forum.core-electronics.com.au/t/pico-dev-and-stemma-qt/16267/6 "2023-02-12T10:49:44Z")

</div>

Okay. Thanks, I just got distracted by ArduBoy. This could be what I want without having to get components

---

<div class="post-metadata">

**Author:** ![John136772](https://yyz2.discourse-cdn.com/flex028/user_avatar/forum.core-electronics.com.au/john136772/32/5416_2.png) [@John136772](https://forum.core-electronics.com.au/u/John136772)\
**Post date:** [12 February 2023 11:20 UTC](https://forum.core-electronics.com.au/t/pico-dev-and-stemma-qt/16267/7 "2023-02-12T11:20:35Z")

</div>

If this is a problem, I would rather solder the wires…
