# Terminal blocks for breadboard

**URL:** <https://forum.core-electronics.com.au/t/terminal-blocks-for-breadboard/3950>\
**Category:** Uncategorized\
**Created:** [19 November 2018 00:34 UTC](https://forum.core-electronics.com.au/t/terminal-blocks-for-breadboard/3950 "2018-11-19T00:34:13Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![Christopher70069](https://avatars.discourse-cdn.com/v4/letter/c/a4c791/32.png) [@Christopher70069](https://forum.core-electronics.com.au/u/Christopher70069)\
**Post date:** [19 November 2018 00:34 UTC](https://forum.core-electronics.com.au/t/terminal-blocks-for-breadboard/3950/1 "2018-11-19T00:34:13Z")

</div>

I am a bit confused about using terminal blocks on breadboards.

1. Should I be even wanting to put terminal block on BB ?

2. Are terminal blocks only used on proto boards and soldered in ?

3. If t’blocks are ok on BB… which to use i.e which “pitch”

thanks in advance

---

<div class="post-metadata">

**Author:** ![Stephen](https://yyz2.discourse-cdn.com/flex028/user_avatar/forum.core-electronics.com.au/stephen/32/1599_2.png) [@Stephen](https://forum.core-electronics.com.au/u/Stephen)\
**Post date:** [19 November 2018 00:48 UTC](https://forum.core-electronics.com.au/t/terminal-blocks-for-breadboard/3950/2 "2018-11-19T00:48:10Z")

</div>

Hi Chis,

I don’t see any reason to use terminal blocks on a breadboard. You could push the wire into the breadboard, so no need for terminal blocks. You could connect much larger wire gauge to a terminal block, but if you’re doing that you are likely exceeding the specs of the breadboard.

If you do decide you want them use 0.1 inch spaced pins.

---

<div class="post-metadata">

**Author:** ![Christopher70069](https://avatars.discourse-cdn.com/v4/letter/c/a4c791/32.png) [@Christopher70069](https://forum.core-electronics.com.au/u/Christopher70069)\
**Post date:** [19 November 2018 00:55 UTC](https://forum.core-electronics.com.au/t/terminal-blocks-for-breadboard/3950/3 "2018-11-19T00:55:46Z")

</div>

Thanks Stephen,

I was coming around to that conclusion… just confirmed.

Just to clarify,  
Screw Terminal Block: 2-Pin, 3.5 mm Pitch, Top Entry (4-Pack) ( POLOLU-2442)  
does 3.5 mm refer to board pin spacing? There are also 2.5mm pitch.  
… and what is spacing of BB pin-holes ?

---

<div class="post-metadata">

**Author:** ![Stephen](https://yyz2.discourse-cdn.com/flex028/user_avatar/forum.core-electronics.com.au/stephen/32/1599_2.png) [@Stephen](https://forum.core-electronics.com.au/u/Stephen)\
**Post date:** [19 November 2018 01:02 UTC](https://forum.core-electronics.com.au/t/terminal-blocks-for-breadboard/3950/4 "2018-11-19T01:02:36Z")

</div>

Hi Chris,

2.5mm pitch is the same as a breadboard.

---

<div class="post-metadata">

**Author:** ![Christopher70069](https://avatars.discourse-cdn.com/v4/letter/c/a4c791/32.png) [@Christopher70069](https://forum.core-electronics.com.au/u/Christopher70069)\
**Post date:** [19 November 2018 01:11 UTC](https://forum.core-electronics.com.au/t/terminal-blocks-for-breadboard/3950/5 "2018-11-19T01:11:28Z")

</div>

Righto.

That’s what I was wanting to clear up. I searched high and low!!

Thanks again Stephen
