# Waveshare ESP32-S3-LCD-4.3 800 x 480 Display

**URL:** <https://forum.core-electronics.com.au/t/waveshare-esp32-s3-lcd-4-3-800-x-480-display/20430>\
**Category:** Support\
**Created:** [11 July 2024 03:18 UTC](https://forum.core-electronics.com.au/t/waveshare-esp32-s3-lcd-4-3-800-x-480-display/20430 "2024-07-11T03:18:09Z")\
**Posts on this page:** 11\
**Page:** 1

<div class="post-metadata">

**Author:** ![David66175](https://avatars.discourse-cdn.com/v4/letter/d/ba8739/32.png) [@David66175](https://forum.core-electronics.com.au/u/David66175)\
**Post date:** [11 July 2024 03:18 UTC](https://forum.core-electronics.com.au/t/waveshare-esp32-s3-lcd-4-3-800-x-480-display/20430/1 "2024-07-11T03:18:09Z")

</div>

Hi All,  
I have just purchased the above [display which incorporates an ESP32](https://core-electronics.com.au/esp32-s3-43inch-capacitive-touch-display-development-board.html) on the display. I have followed the Arduino (2.3.2) installation instructions from Waveshare, and uploaded the code to the board. I have added a couple of print statements to see a bit of what happens, here is the serial output:-

```auto
Panel test example start
Initialize display panel
LCD = 1070516104
Touch = 0
Backlight = 1070516224
Turn off the backlight
Draw color bar from top to bottom, the order is B - G - R
E (30) lcd_panel: esp_lcd_panel_draw_bitmap(33): invalid panel handle
E (30) ESP_PanelLcd: Draw bitmap failed
Turn on the backlight
Touch is not available
Panel test example end

```

So far I have not been able to get any response from the display at all and because there are so many setup variables that are changeable I am reluctant to go down that path.  
If anyone has this display working I would appreciate some help in setting it up.  
Thanks.  
David

---

<div class="post-metadata">

**Author:** ![Pixmusix](https://yyz2.discourse-cdn.com/flex028/user_avatar/forum.core-electronics.com.au/pixmusix/32/9719_2.png) [@Pixmusix](https://forum.core-electronics.com.au/u/Pixmusix)\
**Post date:** [11 July 2024 03:34 UTC](https://forum.core-electronics.com.au/t/waveshare-esp32-s3-lcd-4-3-800-x-480-display/20430/2 "2024-07-11T03:34:56Z")

</div>

Hey @David66175 David.  
Welcome.

> [@David66175](#):
>
> I am reluctant to go down that path.

Fair enough.  
Could you provide a link to the code that you have been following?  
we might be able to read it and provide some insight 🙂

---

<div class="post-metadata">

**Author:** ![David66175](https://avatars.discourse-cdn.com/v4/letter/d/ba8739/32.png) [@David66175](https://forum.core-electronics.com.au/u/David66175)\
**Post date:** [11 July 2024 03:38 UTC](https://forum.core-electronics.com.au/t/waveshare-esp32-s3-lcd-4-3-800-x-480-display/20430/3 "2024-07-11T03:38:31Z")

</div>

Hi Pixmusix,  
Thanks for your reply, here is the link from Waveshare’s documentation. [https://files.waveshare.com/wiki/ESP32-S3-Touch-LCD-4.3/S3-4.3-libraries.zip](https://files.waveshare.com/wiki/ESP32-S3-Touch-LCD-4.3/S3-4.3-libraries.zip)  
and the link to the documentation  
[https://www.waveshare.com/wiki/ESP32-S3-Touch-LCD-4.3#Modify\_the\_Driver](https://www.waveshare.com/wiki/ESP32-S3-Touch-LCD-4.3#Modify_the_Driver)

David

---

<div class="post-metadata">

**Author:** ![Jack](https://yyz2.discourse-cdn.com/flex028/user_avatar/forum.core-electronics.com.au/jack/32/9287_2.png) [@Jack](https://forum.core-electronics.com.au/u/Jack)\
**Post date:** [11 July 2024 03:59 UTC](https://forum.core-electronics.com.au/t/waveshare-esp32-s3-lcd-4-3-800-x-480-display/20430/4 "2024-07-11T03:59:39Z")

</div>

Hi David,

I’ve found ribbon cable connections on displays can be quite sensitive and it is possible it may not be connected properly. Give that one a look first.

It is odd it isn’t defaulting to its errors if the screen isn’t doing anything. I can’t see a section on it’s power requirements but what are you using at the moment to power it?

---

<div class="post-metadata">

**Author:** ![David66175](https://avatars.discourse-cdn.com/v4/letter/d/ba8739/32.png) [@David66175](https://forum.core-electronics.com.au/u/David66175)\
**Post date:** [11 July 2024 04:39 UTC](https://forum.core-electronics.com.au/t/waveshare-esp32-s3-lcd-4-3-800-x-480-display/20430/5 "2024-07-11T04:39:23Z")

</div>

The board has two USB-C inputs (1 for programming, and 1 for serial output) both supply power. I checked the 5V rail - 4.95 V and 3.3V rail 3.4V the display connecter is also well seated, actually I just remembered it came with a demo program programmed in and it was working as expected with only 1 USB plugged in so it doesn’t use much power.  
David

---

<div class="post-metadata">

**Author:** ![Jack](https://yyz2.discourse-cdn.com/flex028/user_avatar/forum.core-electronics.com.au/jack/32/9287_2.png) [@Jack](https://forum.core-electronics.com.au/u/Jack)\
**Post date:** [11 July 2024 06:10 UTC](https://forum.core-electronics.com.au/t/waveshare-esp32-s3-lcd-4-3-800-x-480-display/20430/6 "2024-07-11T06:10:25Z")

</div>

This is odd behaviour. How is your Arduino IDE configured? Can you send a screenshot of the tools dropdown in particular. Hopefully it is a software issue and not a hardware one.

---

<div class="post-metadata">

**Author:** ![lia262073](https://avatars.discourse-cdn.com/v4/letter/l/94ad74/32.png) [@lia262073](https://forum.core-electronics.com.au/u/lia262073)\
**Post date:** [11 July 2024 13:58 UTC](https://forum.core-electronics.com.au/t/waveshare-esp32-s3-lcd-4-3-800-x-480-display/20430/7 "2024-07-11T13:58:43Z")

</div>

Plz check your wirings and also try to test the display in a different platform.

---

<div class="post-metadata">

**Author:** ![David66175](https://avatars.discourse-cdn.com/v4/letter/d/ba8739/32.png) [@David66175](https://forum.core-electronics.com.au/u/David66175)\
**Post date:** [12 July 2024 07:23 UTC](https://forum.core-electronics.com.au/t/waveshare-esp32-s3-lcd-4-3-800-x-480-display/20430/8 "2024-07-12T07:23:44Z")

</div>

I have spent too much time on this at present, so I am going to put it aside for a while, and do some research in my spare time. The two attached images are the tools drop down, and a listing from the serial output port. The board is set as an ESP32\_S3\_LCD\_EV\_BOARD, which is basically what is printed on the PCB.

 ![Screenshot 2024-07-12 at 5.16.06 PM](https://canada1.discourse-cdn.com/flex028/uploads/core_electronics/original/2X/5/59be6850c8717751635541f3ae2c270d1d96cfa9.png)  
 ![Screenshot 2024-07-12 at 5.18.04 PM](https://canada1.discourse-cdn.com/flex028/uploads/core_electronics/original/2X/0/08e35a9b92d25185b48058bce48bb7914fdf55dc.jpeg)

Thanks for the feedback so far guys.  
David

---

<div class="post-metadata">

**Author:** ![Christoph144366](https://avatars.discourse-cdn.com/v4/letter/c/e56c9b/32.png) [@Christoph144366](https://forum.core-electronics.com.au/u/Christoph144366)\
**Post date:** [7 March 2025 23:04 UTC](https://forum.core-electronics.com.au/t/waveshare-esp32-s3-lcd-4-3-800-x-480-display/20430/9 "2025-03-07T23:04:00Z")

</div>

Hi David,

I have this board and also experienced some frustration making it work. Eventually I’ve arrived at a process that works for me - basically a starting template which I build on to make whatever I want. It uses EEZ Studio, a graphical tool to create the gui, which generates LVGL code and inserts it into an Arduino sketch for uploading to the device.

Details are at [https://gitlab.com/chris.willing/lvgl-eezstudio-setup](https://gitlab.com/chris.willing/lvgl-eezstudio-setup)

---

<div class="post-metadata">

**Author:** ![Dan](https://yyz2.discourse-cdn.com/flex028/user_avatar/forum.core-electronics.com.au/dan/32/10815_2.png) [@Dan](https://forum.core-electronics.com.au/u/Dan)\
**Post date:** [10 March 2025 00:37 UTC](https://forum.core-electronics.com.au/t/waveshare-esp32-s3-lcd-4-3-800-x-480-display/20430/10 "2025-03-10T00:37:34Z")

</div>

Hi @Christoph144366

Welcome to the forum!

That’s a neat little program, thanks for sharing!

---

<div class="post-metadata">

**Author:** ![Christoph144366](https://avatars.discourse-cdn.com/v4/letter/c/e56c9b/32.png) [@Christoph144366](https://forum.core-electronics.com.au/u/Christoph144366)\
**Post date:** [10 March 2025 01:03 UTC](https://forum.core-electronics.com.au/t/waveshare-esp32-s3-lcd-4-3-800-x-480-display/20430/11 "2025-03-10T01:03:38Z")

</div>

Thanks Dan,

I’ve actually moved the details to a different location. The old link is redirecting for now but advising I should change the old reference. I can’t edit that now so here is the new link:

- [https://gitlab.com/chris.willing.waveshare/lvgl-eezstudio-setup](https://gitlab.comchris.willing.waveshare/lvgl-eezstudio-setup)
